Variable speed Control under Voltage and Current Limits of a 5-phase PMSM drive in Healthy and Open-Circuited Modes

Archive ouverte : Article de revue

Fall, Ousmane | Charpentier, Jean Frederic | Nguyen, Ngac Ky | Letellier, Paul | Semail, Eric | Kestelyn, Xavier

Edité par HAL CCSD ; Elsevier

International audience. This paper proposes a novel variable speed control strategy of a particular 5-phase Permanent Magnet Synchronous Generator (PMSG) in healthy and faulty modes by taking into account the constraints on voltages and currents. These constraints are related to the converter and machine design. The considered faults are open-circuited phases (one phase, two adjacent phases and two non-adjacent phases). A variable speed control strategy is presented, including flux weakening operations. Based on analytical formulations, a numerical computation is proposed to bring out the torque−speed characteristics. This method allows the determination of the current references which ensure the functioning of a 5-phase PMSG at variable speed while keeping phase voltages and currents below their limits. Theoretical, numerical and experimental results are presented. These results are compared in order to validate the proposed approach.

Consulter en ligne

Suggestions

Du même auteur

Generalized Vectorial Formalism – based multiphase series-connected motors ...

Archive ouverte: Communication dans un congrès

Semail, Eric | 2015-10

Multiphase drives are more and more used in specific applications leading to a necessity of control strategy development. This paper presents the Generalized Vectorial Formalism (GVF) theory to control multiphase series-connected ...

Investigation on Model Predictive Control of a Five-Phase Permanent Magnet ...

Archive ouverte: Communication dans un congrès

Kestelyn, Xavier | 2015-03

The optimal control of electrical drives necessitates to take into account current and voltage limits that are imposed by the power electronics and the electrical machines. Let’s cite for example the flux-weakening operation of el...

Real-Time Validation of a Cascaded Model Predictive Control Technique for a...

Archive ouverte: Communication dans un congrès

Bermudez Guzman, Mario | 2017-07

International audience. Multiphase machines have recently gained importance in the research community for their use in applications where high power density, wide speed range and fault-tolerant capabilities are need...

Du même sujet

Slot/pole Combinations Choice for Concentrated Multiphase Machines dedicate...

Archive ouverte: Communication dans un congrès

Aslan, Bassel | 2011-11

Version de l'éditeur à l'adresse suivante : http://ieeexplore.ieee.org/stamp/stamp.jsp?tp=&arnumber=6119910&isnumber=6119266. This paper presents multiphase permanent magnet machines with concentrated non-overlapped...

Design of Multiphase PM Machine with Fractional Slot Concentrated-Windings ...

Archive ouverte: Thèse

Aslan, Bassel | 2013-10-29

The aim of this thesis is to design an electrical machine dedicated for Mild-Hybrid applications. By providing certain functionalities, this machine can reduce fuel consumption in the vehicle and therefore reduce the amount of rel...

Computation of Optimal Current References for Flux-weakening of Multi-Phase...

Archive ouverte: Communication dans un congrès

Lu, Li | 2012-10-25

International audience. Multi-phase synchronous machines are more and more used in specific applications where high power density, low bus voltage, wide speed range and fault-tolerant capabilities are required. Due ...

Maximum Torque Per Ampere Control Strategy of a 5-phase PM Generator in hea...

Archive ouverte: Communication dans un congrès

Fall, Ousmane | 2014-11

The work presented in this paper aims to propose a control strategy being able to extract efficiently energy from a fixed-pitch marine current turbine associated with a 5–phase Permanent Magnet Synchronous Generator (PMSG) in heal...

Open-Phase Fault-Tolerant Direct Torque Control Technique for Five-Phase In...

Archive ouverte: Article de revue

Bermudez Guzman, Mario | 2017

International audience. Direct torque control (DTC) has been widely used as an alternative to traditional field-oriented control (FOC) methods for three-phase drives. The conventional DTC scheme has been successfull...

Inductances and back-emf harmonics influence on the Torque/Speed characteri...

Archive ouverte: Communication dans un congrès

Scuiller, Franck | 2014-10

In this paper, the study of torque/speed characteristic for five-phase Surface-mounted Permanent Magnet (SPM) machine is carried out. With considering several hypothesis (linear magnetic modelling, only first and third harmonic te...

Chargement des enrichissements...